Ver cesta (0 Producto) Mi cuentaMostrar lista de la compraIr a caja

Tintes Ignite

Tintes Ignite

Ignite Colores Fluorescentes

La línea de colorantes fluorescentes Ignite es compatible con las gomas de poliuretano, plásticos de uretano, espumas de poliuretano (rígidas y flexibles) y también con siliconas. El "brillo" del efecto fluorescente se maximiza bajo la luz ultravioleta "luz negra". Podemos conseguir un efecto de color más dramático cuando añadimos el colorante Ignite a una goma de uretano transparente como Clear Flex 50 o a una resina translúcida de plástico como Smooth-Cast 325.

Con el Nuevo "Ignite 9 pack" tiene la oportunidad de experimentar cada color sin tener que gastar mucho dinero.

¿Qué hace que las piezas fabricadas con los pigmentos Ignite ® parecen que brillen?
Cuando se agrega "Ignite color fluorescente" a un material de uretano, la luz ultravioleta del material curado es visible para el ojo. Pasa lo contrario con las piezas hechas con colorantes muy fuertes como los colores SO-Strong. Con Ignite las piezas parecen más brillante a la luz ambiental y parecen que brillan bajo la luz ultravioleta.

Boletín Técnico y Carta de Colores

Tintes Ignite

  • Ignite Verde /120ml

    Colores fluorescentes para PU y siliconas. Color Verde. Bote 120ml

    22,50 EUR (precio sin 21% IVA .)

  • Ignite Magenta /120ml

    Colores fluorescentes para PU y siliconas. Color Magenta. Bote 120ml

    22,50 EUR (precio sin 21% IVA .)

  • Ignite Naranja /120ml

    Colores fluorescentes para PU y siliconas. Color Naranja Bote 120ml

    22,50 EUR (precio sin 21% IVA .)

  • Ignite Rosa / 120ml

    Colores fluorescentes para PU y siliconas. Color Rosa. Bote 120ml

    22,50 EUR (precio sin 21% IVA .)

  • Ignite Amarillo / 120ml

    Colores fluorescentes para PU y siliconas. Color Amarillo. Bote 120ml

    22,50 EUR (precio sin 21% IVA .)

  • Ignite Azul /120ml

    Colores fluorescentes para PU y siliconas, Azul, 120ml

    22,50 EUR (precio sin 21% IVA .)

  • Ignite Rojo / 120ml

    Colores fluorescentes para PU y siliconas. Color Rojo. Bote 120ml

    22,50 EUR (precio sin 21% IVA .)

  • Ignite 9 colores / 200gr

    Ignite kit de 9 colores, 200gr

    39,25 EUR (precio sin 21% IVA .)

  • Ignite Blanco / 120ml

    Colores fluorescentes para PU y siliconas, Blanco, 120ml

    18,30 EUR (precio sin 21% IVA .)

To get you started, we offer the following colorant loading levels. Results may vary.

By Weight Using A Gram Scale: Add Ignite® colorant at a ratio of between 0.5% - 1.5% of the total weight (Parts A + B mixed) of the material being cast. 1% pigment yields the best results. Adding more than 1.5% by weight offers no benefit and is a waste of the colorant. Too much colorant may cause cure inhibition.

By Volume Measured In Drops: Add 30 drops of Ignite™ per 3 oz (88 ml) of mixed urethane material. If using a translucent material (like Smooth-Cast 325) you can use 15 drops to maintain translucency of the material.

Pre-Mix Before Using: Ignite® colorants are pigment dispersions and may separate over time. They must be thoroughly pre-mixed in the container before using with a liquid urethane product.

Directions For Use: After dispensing the required amount of urethane material Parts A and B into measuring containers, add colorant to Part B and mix thoroughly. Combine Parts A and B into a mixing container and mix as directed by the urethane product technical bulletin. Blending Colors - You can combine different colors on a pallete to create a custom color before adding to liquid urethane product as directed above.

There are no issues when using this product with urethane rubbers, plastics and foams or tin-catalyzed silicones. However…Ignite® pigments will drastically thicken platinum silicone rubber. Adding Ignite® colorants to a Smooth-On platinum cure silicone such as Dragon Skin® will make the silicone notably thicker, thereby affecting its ability to be vacuum degassed. Recommended loading maximum is 1% Ignite pigment by weight. An option for using Ignite® colorants with a platinum silicone may be to use pigmented material as paint for brushing on to an existing platinum silicone casting or appliance. You can use Ignite® colorants with our Psycho Paint® system.

Smooth-On offers this color guide as a general reference only and assumes no responsibility for color accuracy or matching. Results will vary from one material to another. The end user is solely responsible for determining color suitability and accuracy. Small scale testing is recommended. User determines amount to add; If this is your first time adding color tint or pigment to a urethane, epoxy or silicone system, you may want to test the color effect by adding a few drops to a small amount of urethane material and observe the outcome. It may take a few test castings to attain the desired color outcome.

Looking for a clear fluorescent additive? Cryptolyte® is a clear additive that can be added to urethane or silicone materials that will cause cured material to glow a bright blue when exposed to UV light (black light).


Let us help you find your way.

The list below may help you find what you are looking for via an alternative path.

Información Contacto Tarifas de envío Proyectos Clientes Marcas Aplicaciones Branches

su ventanilla única para materiales de modelado en 3D