gtag('config', 'G-J1B3LVWC4M');
Ver cesta (0 Producto) Mi cuentaMostrar lista de la compraIr a caja

Smooth-Sil ™ 950 /5kg

Smooth-Sil 950 / 5 kg.

Las siliconas de platino Smooth-On Smooth-Sil ™ curan a temperatura ambiente con una contracción insignificante. Con diferentes durezas para elegir, los productos Smooth-Sil ™ ofrecen una gran versatilidad y son adecuados para hacer moldes de producción de cualquier configuración, grande o pequeña. Estas siliconas presentan una buena resistencia química, a la abrasión y al calor. Materiales como yesos, hormigón, cera, aleaciones de metales de bajo punto de fusión o resinas (uretano, epoxi o poliéster) se pueden fundir en estos cauchos de silicona sin un agente de liberación.

Las siliconas de platino Smooth-Sil ™ se utilizan para la creación rápida de prototipos, la fundición de cera (fundiciones y fabricantes de velas), la restauración arquitectónica y la fundición de hormigón.
Smooth-Sil ™ 950 es adecuado para aplicaciones relacionadas con alimentos

158,27 EUR

precio sin 21% IVA .
unidad


Instructions

Safety – Use in a properly ventilated area (“room size” ventilation). Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk. Wear vinyl gloves only. Latex gloves will inhibit the cure of the rubber.

Store and use material at room temperature 23°C. Warmer temperatures will drastically reduce working time and cure time. Storing material at warmer temperatures will also reduce the usable shelf life of unused material. These products have a limited shelf life and should be used as soon as possible.

Cure Inhibition – Addition-cure silicone rubber may be inhibited by certain contaminants in or on the pattern to be molded resulting in tackiness at the pattern interface or a total lack of cure throughout the mold. Latex, tin-cure silicone, sulfur clays, certain wood surfaces, newly cast polyester, epoxy or urethane rubber my cause inhibition. If compatibility between the rubber and the surface is a concern, a small-scale test is recommended. Apply a small amount of rubber onto a non-critical area of the pattern. Inhibition has occurred if the rubber is gummy or uncured after the recommended cure time has passed.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

To prevent inhibition, one or more coatings of a clear acrylic lacquer applied to the model surface is usually effective. Allow any sealer to thoroughly dry before applying rubber. Note: Even with a sealer, platinum silicones will not work with modeling clays containing heavy amounts of sulfur. Do a small scale test for compatibility before using on your project.

Applying A Release Agent - Although not usually necessary, a release agent will make demolding easier when pouring into or over most surfaces. Ease Release® 200 is a proven release agent for making molds with silicone rubber. Mann Ease Release® products are available fromForm X

IMPORTANT:
To ensure thorough coverage, lightly brush the release agent with a soft brush over all surfaces of the model. Follow with a light mist coating and let the release agent dry for 30 minutes. If there is any question about the effectiveness of a sealer/release agent combination, a small-scale test should be made on an identical surface for trial.

MEASURING & MIXING...

Before you begin, pre-mix Part B thoroughly to re-disperse pigments that may have settled. Using a gram scale, dispense required amounts of parts A and B into a mixing container and mix for 3 minutes. Scrape the sides and bottom of the container several times. After mixing parts A and B, vacuum degassing is recommended to eliminate any entrapped air. Vacuum material for 2-3 minutes (0,98 bar), making sure that you leave enough room in container for product expansion.

For best results, pour your mixture in a single spot at the lowest point of the containment field. Let the rubber seek its level up and over the model. A uniform flow will help minimize entrapped air. The liquid rubber should level off at least 1.3 cm over the highest point of the model surface.

Curing / Post Curing - Allow rubber to cure as prescribed at room temperature 23°C before demolding. Do not cure rubber where temperature is less than 18°C. Optional: Post curing the mold will aid in quickly attaining maximum physical and performance properties. After curing at room temperature, expose the rubber to 80°C for 2 hours and 100°C for one hour. Allow mold to cool to room temperature before using.

Using The Mold - When first cast, silicone rubber molds exhibit natural release characteristics. Depending on what is being cast into the mold, mold lubricity may be depleted over time and parts will begin to stick. No release agent is necessary when casting wax or gypsum. Applying a release agent such as Ease Release® 200 (available from Form X) prior to casting polyurethane, polyester and epoxy resins is recommended to prevent mold degradation.

Thickening Smooth-Sil™ Silicones - THI-VEX® is made especially for thickening Smooth-On’s silicones for vertical surface application (making brush-on molds). Different viscosities can be attained by varying the amount of THI-VEX®. See the THI-VEX® technical bulletin (available from Smooth-On or your Smooth-On distributor) for full details.

Thinning Smooth-Sil™ Silicones - Smooth-On’s Silicone Thinner® will lower the viscosity of Smooth-Sil™ for easier pouring and vacuum degassing. A disadvantage is that ultimate tear and tensile are reduced in proportion to the amount of Silicone Thinner® added. It is not recommended to exceed 10% by weight of total system (A+B). See the Silicone Thinner® technical bulletin (available from Smooth-On or your Smooth-On distributor) for full details.

Mold Performance & Storage - The physical life of the mold depends on how you use it (materials cast, frequency, etc.). Casting abrasive materials such as concrete can quickly erode mold detail, while casting non-abrasive materials (wax) will not affect mold detail. Before storing, the mold should be cleaned with a soap solution and wiped fully dry. Two part (or more) molds should be assembled. Molds should be stored on a level surface in a cool, dry environment.

Ayuda para elegir

Todos nuestros productos enumerados por aplicaciones: "Lifecasting", Escultura, Moldes, Fundición, Maquillaje FX, Réplicas, Dientes y Kits de aprendizaje.

  • Moldes

    una amplia gama de materiales rígidos y flexibles para fabricar moldes de: Silicona, caucho de Poliuretano, resina de Poliuretano, Poliester, yesos especiales, etc.

  • Réplicas

    Materiales flexibles y rígidos para colar en el interior de los moldes. Aqui encontrará resinas bicomponentes de poliuretano, epoxi y poliester en diferentes durezas. Así como espumas rígidas y flexibles, etc.

  • special properties

  • Espumas

    Espuma flexible líquida, Espuma rígida líquida, Bloques de espuma rígida

  • Composites

    Resinas de poliester para laminar, resinas de colada, gelcoat, masillas, pastas y accesorios.

  • Restauración

    una amplia variedad de materiales para la restauración de ornamentos en edificios. Se pueden utilizan tanto en el interior como en el exterior.

  • Prototipos

    Materiales utilizados para prototipado rápido

  • Acabados & Fundición

    Todos los productos que Usted necesita. Aquí encontrará las resinas que puede utilizar, polvos metálicos, cargas, pátinas, etc.

  • Textil

  • Plásticos para Brocha

    Plásticos que se pueden aplicar con brocha sobre esculturas hechas en Poliestireno o en espuma de poliuretano.

  • Cosplay

    Productos para hacer tus propios disfraces y accesorios de cosplay

  • EZ Spray Productos

    es un sistema de pulverización para gomas, plásticos y espumas. Ahorra tiempo y costos laborales en comparación con los métodos de aplicación manual

FormX Newsletter Boletin informativo Información Contacto Tarifas de envío Proyectos Clientes Condiciones de Venta Marcas we have vacancies Aplicaciones Branches FormX Academy

su ventanilla única para materiales de modelado en 3D

Utilizamos cookies para optimizar nuestro sitio web y ofrecerle la mejor experiencia en línea posible. Al hacer clic en "Aceptar todo", usted acepta esto. ¿Más Información?