Soma Foama ® es una espuma de silicona de platino bicomponente que se aplica por colada. Es una silicona muy versátil y fácil de usar. Soma Foama ® se puede verter en un molde o sobre otras superficies. Si añadimos los pigmentos de silicona Silc-Pig ® podemos conseguir colores vibrantes. Una vez curada, la espuma es resistente al calor (resiste hasta 176°), a la oxidación, al agua y a los rayos UV. Soma Foama ® se puede utilizar en efectos especiales, en aplicaciones industriales y en trabajos muy especiales. Esto incluye la realización de objetos rellenos de espuma, asientos acolchados, ortopedia / traumatología, encapsulación de circuitos eléctricos y amortiguación de vibraciones.
Soma Foama ® está disponible en dos densidades; 15 lb. y 25 lb.
Soma Foama ® 15 - Mezcla 2 partes A: 1Parte B por volumen. Expande 4 veces el volumen inicial con una estructura celular uniforme y una densidad de 240 kg. / m3. Soma Foama ® 25 - Mezcla 1 Parte A: 1Parte B por volumen. Expande 2-3 veces el volumen inicial con una estructura celular uniforme y una densidad de 400 kg / m3.
Los Mezcladores de Turbina pueden ser usados para mezclar productos bicomponentes de forma rápida. El mezclador se puede fijar a cualquier taladro de velocidad variable.
Balanza de cocina. Pesa hasta 2 kg. con la precisión de un gramo.
16,70 EUR(precio sin 21% IVA .)
Instructions
Store and use at room temperature (73°F/23°C). These products have a limited shelf life and should be used as soon as possible. Good room size ventilation is essential. Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk.
Cure Inhibition - Addition cured silicones may be inhibited by certain contaminants such as sulfur, polyesters, certain wood surfaces, epoxies, urethane rubber and tin catalyzed silicones resulting in tackiness at the pattern interface or a total lack of cure throughout the mold. If compatibility between the rubber and the surface is a concern, a small-scale test is recommended. Apply a small amount of foam onto a non-critical area of the pattern. Inhibition has occurred if the matrerial is gummy or uncured after the recommended cure time has passed. This product will not cure against tin-based silicone rubbers.
Applying A Release Agent - Soma Foama® will stick to some surfaces and a release agent may be necessary to facilitate demolding. When casting Soma Foama® into or over other platinum silicones, apply Ease Release® 200 prior to applying foam. IMPORTANT: To ensure thorough coverage, lightly brush the release agent with a soft brush over all surfaces. Let the release agent dry for 15 minutes.
Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.
Mixing - Mixing can be done by hand or using a drill and a mixer attachment, such as a “squirrel” mixer. After dispensing required amounts of Parts A and B into mixing container, mix thoroughly for 30 seconds. Stir quickly and deliberately, making sure you scrape the sides and bottom of the mixing container several times. Be careful not to splash material out of the container. Remember, foam cures quickly. Do not delay between mixing and pouring. Elevated temperatures will result in a reduced pot life and cure time.
Warning - A small amount of Hydrogen gas is released as part of the A:B reaction. Use only with adequate ventilation and do not breathe fumes. Also do not smoke or have other ignition sources in proximity to this product during mixing and pouring.
Pouring - For best results, pour your mixture in a single spot at the lowest point of the containment field and let the mixture seek its own level.
Handling Strength is 20 minutes with full cure in 1 hour at room temperature. Foam color will darken over time. Adding Silc-Pig® silicone pigments will help stabilize color of cured foam. To adhere Soma Foama® to other platinum silicones, best adhesion is realized when poured against newly cured platinum silicone rubber.
Results May Vary: This material is subject to variables such as high or low environmental temperatures. A small test to determine how material performs for your application is recommended.
Improve Surface Finish and Minimize Voids With Back Pressure - Use a board that will completely cover the mold opening. Using a ¾” (2 cm) drill bit, drill 3 holes in the board spaced a few inches / cm apart. Make sure that, when the board is placed over the mold opening, the holes are over the mold cavity and rising foam will be able to make it through. Apply Ease Release® 200 thoroughly too both sides of the board and into the drilled holes. Mix and pour foam into mold cavity and place board over mold opening. Hold board firmly in place. As foam rises in the mold cavity, some foam will grow out of the drilled holes. After the foam stops growing, you can let go of the board. Do not demold for at least 20 minutes.
Demold - After 20 minutes, cut excess material that came through holes. Gently remove board and casting.
The Supergloves Bluple nitrile disposable glove is made from top quality nitrile. The Bluple nitrile is, despite its smaller thickness (3.2 mil.), Strong and particularly comfortable due to its hig...
The Supergloves Bluple nitrile disposable glove is made from top quality nitrile. The Bluple nitrile is, despite its smaller thickness (3.2 mil.), Strong and particularly comfortable due to its hig...
The Supergloves Bluple nitrile disposable glove is made from top quality nitrile. The Bluple nitrile is, despite its smaller thickness (3.2 mil.), Strong and particularly comfortable due to its hig...
The Supergloves Bluple nitrile disposable glove is made from top quality nitrile. The Bluple nitrile is, despite its smaller thickness (3.2 mil.), Strong and particularly comfortable due to its hig...
Máscara para pulverizar pintura, cómoda, fácil de usar y fácil de limpiar. Tiene una resistencia a la respiración muy baja debido a la gran área de superficie de los filtros.....
Aerosol de silicona. Nos permite aplicar una capa muy gruesa. ER400 se utiliza en trabajos donde los otros desmoldeantes resultan insuficientes. Acabado brillante. Aerosol 400 gr
Acmos 82-2405. Desmoldeante universal de cera lavable, tiene un acabado mate. Aerosol 400 gr
12,32 EUR(precio sin 21% IVA .)
garantía de precios más bajos
En FormX nos hemos especializado en la importación de materiales para el diseño fabricados en EEUU. Nos comprometemos a ofrecer estos productos a los precios más bajos.
Todos nuestros productos enumerados por aplicaciones: "Lifecasting", Escultura, Moldes, Fundición, Maquillaje FX, Réplicas, Dientes y Kits de aprendizaje.
una amplia gama de materiales rígidos y flexibles para fabricar moldes de: Silicona, caucho de Poliuretano, resina de Poliuretano, Poliester, yesos especiales, etc.
Materiales flexibles y rígidos para colar en el interior de los moldes. Aqui encontrará resinas bicomponentes de poliuretano, epoxi y poliester en diferentes durezas. Así como espumas rígidas y flexibles, etc.