Ecoflex™ Gel /0,91 kg

Ecoflex Gel / 0.9 kg.

Ecoflex ® GEL es un gel suave y pegajoso de silicona de platino. Este caucho de silicona ha sido pensado para crear aplicaciones de silicona en maquillaje, objetos amortiguadores, juntas, encapsulados y otras aplicaciones que requieren un material de silicona muy muy suave. Ecoflex ® GEL tiene una dureza Shore A / 000-35, esto está por debajo de la escala de dureza Shore A / 00. Debido a que Ecoflex ® GEL es un producto tan suave, se puede utilizar en efectos especiales como un gel de silicona para el llenado y encapsulado de prótesis. Se pueden conseguir una grán variedad de efectos de color mezclando esta silicona con los pigmentos Silc Pig ®. Como Ecoflex GEL, una vez curado, es un producto muy pegajoso, en algunas aplicaciones se recomienda encapsular Ecoflex ® GEL con otras siliconas de platino que no sean pegajosas, como la Dragon Skin FX Pro. BaldCap esotro producto adecuado para encapsular. Ecoflex ® GEL se mezcla 1A : 1B en peso o en volumen y cura a temperatura ambiente 23 ° C con una contracción insignificante. Al mezclar EcoFlex con el aditivo Slacker, podemos conseguir gelatinas de silicona extremadamente blandas que imitan perfectamente el cuerpo humano. Con esta silicona podemos conseguir efectos carne y piel muy realistas. A+B= 0,9 kg.

Instructions

Preparation - Materials should be stored in and used at room temperature 23°C. These products have a limited shelf life and should be used as soon as possible. Rubber may be inhibited by sulfur based clays resulting in tackiness at the surface interface or a total lack of cure throughout the mold.

If compatibility between the rubber and the surface is a concern, a small-scale test is recommended. Apply a small amount of rubber onto a non-critical area. Inhibition has occurred if the rubber is gummy or uncured after the recommended cure time has passed.

USING ECOFLEX™ GEL FOR MAKING SILICONE PROSTHETIC MAKEUP APPLIANCES - Ecoflex™ GEL can be used as a gel filler for creating silicone prosthetic appliances. In most cases, Ecoflex™ GEL should be encapsulated. For example, Dragon Skin™ FX-Pro can be stippled onto a mold surface (e.g. Shell Shock™ released with Ease Release™ 200) to create a membrane. Ecoflex™ GEL can then be poured or injected into the mold to create a soft gel prosthetic encapsulated with strong, non-tacky Dragon Skin™ FX-Pro silicone.

Applying a Release Agent - Although not always necessary, a release agent will make demolding easier when casting into most surfaces. Ease Release™ 200 available from Form x is a proven release agent for releasing silicone from silicone or other surfaces.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

MEASURING & MIXING - Before you begin, pre-mix Part B thoroughly. After dispensing required amounts of Parts A and B into mixing container (1A:1B by volume or weight), mix thoroughly making sure that you scrape the sides and bottom of the mixing container several times. For best results, ‘double mix’ the material by pouring the mixture into a new container, then continuing to mix until material is thoroughly blended.

Pouring - For best results, pour your mixture in a single spot at the lowest point of the containment field or mold. Let the rubber seek its own level. A uniform flow will help minimize entrapped air.

Curing - Allow rubber to cure for 2 hours at room temperature 23°C before demolding. Time to demold can be reduced with mild heat or by adding an appropriate amount of Plat-Cat™ cure accelerator. The pot life and cure times can be extended using Slo-Jo™ cure retarder. Do not cure rubber where temperature is less than 18°C.