gtag('config', 'G-J1B3LVWC4M');
Ver cesta (0 Producto) Mi cuentaMostrar lista de la compraIr a caja

Mold Max™ 15T /4,5 kg

MM 15 T translúcida / 4,5 kg.

La silicona Mold Max ™ 15T es un compuesto de caucho de silicona curado con estaño translúcido de color blanco agua que tiene una resistencia al desgarro y propiedades de trabajo excepcionales.

Cuenta con el catalizador "Libra ™" de Smooth-On para una larga vida útil de la biblioteca. Mezclado 100A: 10B por peso, se recomienda la desgasificación al vacío para desairear.

El caucho cura durante la noche a temperatura ambiente. Las siliconas Mold Max ™ "T" se pueden espesar con el espesante Thi-Vex ™ para aplicar con brocha y efectos.

Características

- Similar en apariencia a las siliconas de platino premium Dragon Skin ™ de Smooth-On

- Las siliconas Mold Max ™ "T" son una alternativa menos costosa para crear efectos de piel animatrónicos.

- Se puede lograr un número infinito de efectos de color agregando pigmentos de silicona Silc Pig ™ o polvos de efectos Cast Magic ™.

Dureza 15 A - Vida útil 45 minutos - Tiempo de curado 24 horas - Alargamiento @ rotura 600%

más información acerca de la Mold Max:

moldmaxseriestb.pdf [20 KB]

113,00 EUR

precio sin 21% IVA .
unidad


Instructions

Important: you must weigh Part A & B components using a gram scale to be successful with Mold Max™ 15T.

NOTE: Mold Max™ ‘T’ series silicones should NOT be used to make molds for casting Crystal Clear™ or Clear Flex™ Series urethanes.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

Safety –
Use in a properly ventilated area (“room size” ventilation). Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk. Wear vinyl gloves only. Latex gloves will inhibit the cure of the rubber.

Store and use material at room temperature 23°C. Storing material at warmer temperatures will also reduce the usable shelf life of unused material. These products have a limited shelf life and should be used as soon as possible.

Applying a Sealer / Release Agent - Mold Max™ rubber may be inhibited by sulfur based clays resulting in tackiness at the pattern interface or a total lack of cure throughout the mold. If compatibility between the rubber and the surface is a concern, a small-scale test is recommended. Apply a small amount of rubber onto a non-critical area of the pattern. Inhibition has occurred if the rubber is gummy or uncured after the recommended cure time has passed. To prevent inhibition, a “barrier coat” of clear acrylic lacquer sprayed directly onto the pattern is usually effective. Allow to thoroughly dry.

Although not usually necessary, a release agent will make demolding easier when pouring into or over most surfaces. Ease Release™ 200 is a proven release agent for making molds with silicone rubber and for releasing new silicone from cured silicone. Mann Ease Release™ products are available from Form X

Measuring & Mixing -
Before you begin, pre-mix Part B thoroughly to re-disperse pigments that may have settled. Using a gram scale, dispense required amounts of parts A and B into a mixing container and mix for 3 minutes. Scrape the sides and bottom of the container several times. After mixing parts A and B, vacuum degassing is recommended to eliminate any entrapped air in liquid rubber. Your vacuum pump must pull a minimum of 1 Bar / 100 KPa. Leave enough room in container for material expansion. Vacuum material until it rises, breaks and falls. Vacuum for 1 minute after material falls.

Pouring / Curing / Post Curing - For best results, pour your mixture in a single spot at the lowest point of the containment field. Let the rubber seek its level up and over the model. A uniform flow will help minimize entrapped air. The liquid rubber should level off at least 1.3 cm over the highest point of the model surface. Allow the mold to cure overnight (at least 16 hrs) at room temperature 23°C before demolding. Post curing the mold an additional 4 hours at 65°C will eliminate any residual moisture and alcohol that is a by product of the condensation reaction that can inhibit the cure of some urethane resins and rubbers. Allow mold to cool to room temperature before using. Do not cure rubber where temperature is less than 18°C.

Thickening Mold Max™ Silicones For Brush-on Application - THI-VEX™ is made especially for thickening Smooth-On’s Mold Max™ 15 T silicone for vertical surface application (making brush-on molds). Different viscosities can be attained by varying the amount of THI-VEX™. Apply a thin coat of rubber. Wait for rubber to become “tacky” before applying next coat. Final mold thickness should be at least 1 cm. Allow rubber to cure overnight before applying support shell. See the THI-VEX™ technical bulletin (available from Smooth-On or your SmoothOn distributor) for full details.

Accelerating Mold Max™ Silicones - Accel-T™ Silicone Rubber Accelerator will accelerate the cure time of Mold Max™ silicone rubbers. Accel-T™ can be used with Mold Max™ 10T. Note: working time is reduced in proportion to the amount of Accel-T™ added. See the technical bulletin for Accel-T™ (available from Smooth-On or your Smooth-On distributor) for exact mix ratios and cure times. Using these accelerators will result in a shorter library life of the mold.

Thinning Mold Max™ Silicones - Silicone Thinner™ is a non-reactive silicone fluid that will lower the mixed viscosity of tin cure (condensation) or platinum cure (addition) silicone rubber products. Silicone Thinner™ offers the following advantages: [1] A lower mixed viscosity (A+B) means that the rubber will de-air faster when vacuuming; [2] Mixed rubber (A+B) will flow better over intricate model detail; [3] Silicone Thinner™ will lower the ultimate shore hardness (durometer) of cured silicone rubber; [4] Pot life (working time) is increased in proportion to the amount of Silicone Thinner™ used. A disadvantage is that ultimate tear and tensile are reduced in proportion to the amount of Silicone Thinner™ added, however knotty tear properties of the Mold Max™ Series rubbers are unaffected. It is not recommended to exceed 10% by weight of total system (A+B).

Mold Performance & Storage - The physical life of the mold depends on how you use it (materials cast, frequency, etc.). Casting abrasive materials such as concrete can quickly erode mold detail, while casting non-abrasive materials (wax) will not affect mold detail. Before storing, the mold should be cleaned with a soap solution and wiped fully dry. Two part (or more) molds should be assembled. Molds should be stored on a level surface in a cool, dry environment.

Ayuda para elegir

Todos nuestros productos enumerados por aplicaciones: "Lifecasting", Escultura, Moldes, Fundición, Maquillaje FX, Réplicas, Dientes y Kits de aprendizaje.

  • Moldes

    una amplia gama de materiales rígidos y flexibles para fabricar moldes de: Silicona, caucho de Poliuretano, resina de Poliuretano, Poliester, yesos especiales, etc.

  • Réplicas

    Materiales flexibles y rígidos para colar en el interior de los moldes. Aqui encontrará resinas bicomponentes de poliuretano, epoxi y poliester en diferentes durezas. Así como espumas rígidas y flexibles, etc.

  • special properties

  • Espumas

    Espuma flexible líquida, Espuma rígida líquida, Bloques de espuma rígida

  • Composites

    Resinas de poliester para laminar, resinas de colada, gelcoat, masillas, pastas y accesorios.

  • Restauración

    una amplia variedad de materiales para la restauración de ornamentos en edificios. Se pueden utilizan tanto en el interior como en el exterior.

  • Prototipos

    Materiales utilizados para prototipado rápido

  • Acabados & Fundición

    Todos los productos que Usted necesita. Aquí encontrará las resinas que puede utilizar, polvos metálicos, cargas, pátinas, etc.

  • Textil

  • Plásticos para Brocha

    Plásticos que se pueden aplicar con brocha sobre esculturas hechas en Poliestireno o en espuma de poliuretano.

  • Cosplay

    Productos para hacer tus propios disfraces y accesorios de cosplay

  • EZ Spray Productos

    es un sistema de pulverización para gomas, plásticos y espumas. Ahorra tiempo y costos laborales en comparación con los métodos de aplicación manual

FormX Newsletter Boletin informativo Información Contacto Tarifas de envío Proyectos Clientes Condiciones de Venta Marcas we have vacancies Aplicaciones Branches FormX Academy

su ventanilla única para materiales de modelado en 3D

Utilizamos cookies para optimizar nuestro sitio web y ofrecerle la mejor experiencia en línea posible. Al hacer clic en "Aceptar todo", usted acepta esto. ¿Más Información?